Aerial Amplifiers, Signal Distributors and Signal Boosters

A common cause of interference is the coaxial cable from the aerial to your TV. The cables can fill with water (especially old cables), and sometime long cables (especially if not well shielded) can act as giant aerials picking up all kinds of interference. Adding an amplifier can sometimes make things worse. One way improve things is to rewire with new good quality shielded cable and/or to locate the amplifier as close to the aerial as possible so you are not amplifying the interference. This is why aerial amplifiers are often found in lofts. Putting an amplifier next to the TV with the poor signal will only amplify the poor signal.

You can also use masthead amplifiers which amplify the signal at its strongest point (the aerial itself).

This in-line satellite amplifier is designed to be connected between a satellite dish and a receiver. Used to boost a signal over a long cable run. The LNB switching voltage is used to power the amplifier. The gain is 18dB.

£3.99

The price listed includes VAT and delivery to anywhere in the UK.

The Labgear CA121 is a compact aerial amplifier with a single input and 2 outputs. Its lightweight compact design makes it ideal for use in lofts where no mains power supply is available. The Labgear CA121 is designed to help get the best from digital satellite systems - allowing distribution of digital satellite signals and control of digital satellite receivers.

The Labgear CA121 is ideal for Sky TV distribution because it can be powered from the RF output on the Sky box. To switch on the RF2 power output use your Sky remote - and press - "Services, 4, 0, 1, Select." This means that it can be used with Magic Eye remote control extenders.

• Powered either from a digital satellite receiver’s RF2 9VDC output supply or a separate 12VDC power supply
• Provides power to all remote IR receivers 9V 15mA per outlet maximum
• Can be used with MRX120 distribution systems as well as digilink accessories MRX955
• Short circuit protection - if a short circuit occurs on one port it will not shut down the whole amplifier and will continue to operate the other ports
• Gain per port: 10dB
• Noise figure: 4dB
• Connectors: F type (Please see - Coaxial Cable Accessories)

£9.99

The price listed includes VAT and delivery to anywhere in the UK.

The Labgear CA141 is a compact aerial amplifier with a single input and 4 outputs. Its lightweight compact design makes it ideal for use in lofts where no mains power supply is available. The Labgear CA141 is designed to help get the best from digital satellite systems - allowing distribution of digital satellite signals and control of digital satellite receivers.

The Labgear CA141 is ideal for Sky TV distribution because it can be powered from the RF output on the Sky box. To switch on the RF2 power output use your Sky remote - and press - "Services, 4, 0, 1, Select." This means that it can be used with Magic Eye remote control extenders.

• Powered either from a digital satellite receiver’s RF2 9VDC output supply or a separate 12VDC power supply
• Provides power to all remote IR receivers 9V 15mA per outlet maximum
• Can be used with MRX120 distribution systems as well as digilink accessories MRX955
• Short circuit protection - if a short circuit occurs on one port it will not shut down the whole amplifier and will continue to operate the other ports
• Gain per port: 8dB
• Noise figure: 4dB
• Connectors: F type (Please see - Coaxial Cable Accessories)

£12.99

The price listed includes VAT and delivery to anywhere in the UK.

SLx4 is designed to increase and improve TV and FM signals. Outputs for up to 4 TVs. More information on the SLx4.

£19.99

The price listed includes VAT and delivery to anywhere in the UK.

The Labgear MSA262 two inputs (UHF and VHF) so could be used for VHF/FM/DAB or UHF, it can also be used with Sky or as an aerial distribution amplifier. There are six outputs (8dB per port) and one full power output (18dB) for connection to another amplifier or a passive splitter or tap. The Labgear MSA262 has line powering so it could also be used to power a mast head amplifier. More information on the Labgear MSA262 Distribution Amplifier.

£18.99

The price listed includes VAT and delivery to anywhere in the UK.

SLx6 is designed to increase and improve TV and FM signals. Outputs for up to 6 TVs. More information on the SLx6.

£24.50

The price listed includes VAT and delivery to anywhere in the UK.

The HQ ANT AMP8 is designed for TV only (no FM input). The HQ ANT AMP8 is a wall mountable (mounting screws are provided) . It has an adjustable gain control (0 - 10dB) and the maximum gain is 16dB. More information on the HQ ANT AMP8.

£21.99

The price listed includes VAT and delivery to anywhere in the UK.

SLx8 is designed to increase and improve TV and FM signals. Outputs for up to 8 TVs. More information on the SLx8.

£27.99

The price listed includes VAT and delivery to anywhere in the UK.

SLx2B is designed to increase and improve TV and FM signals. Small unobtrusive unit designed to boost the signal to up to two TVs. Has integrated Digital By-pass for use with SLx Link to allow control of Sky Receivers from additional TVs. More information on the SLx2B.

£15.99

The price listed includes VAT and delivery to anywhere in the UK.

The Labgear DA222BP is a VHF/UHF dual input 2 output amplifier with digi bypass. The digi bypass means that it can be used with Sky boxes and magic eye remote control return devices such as the SLx Link. The Labgear DA222BP is a professional mains powered distribution amplifier designed with enhanced TETRA filtering to negate the use of external filters. This DA222BP distribution amplifier is mainly intended for use in a single house or flat to distribute and control the output from digital satellite receivers. The Labgear DA222BP has screw on F-Plug connections. The Labgear DA222BP has screw on F-Plug connections. More information on the Labgear DA222BP.

£18.50

The price listed includes VAT and delivery to anywhere in the UK.

£23.99

The price listed includes VAT and delivery to anywhere in the UK.

SLx6B is designed to increase and improve TV and FM signals. Outputs for up to 6 TVs. Has integrated Digital By-pass for use with SLx Link to allow control of of Sky Receivers from additional TVs. More information on the SLx6B.

£27.50

The price listed includes VAT and delivery to anywhere in the UK.

SLx8 is designed to increase and improve TV and FM signals. Outputs for up to 8 TVs. More information on the SLx8B.

£29.99

The price listed includes VAT and delivery to anywhere in the UK.

SLx Gold four output aerial amplifier with F-plug connections. Designed with the professional aerial installer in mind. Digital satellite compatible. Uses screw on F-plug connections, which are gold plated. Complete with built in Tetra filter to reduce interference from emergency services Tetra radios. Built in surge and spike protection. Built in short circuit protection. Can also be used for DAB or FM radio as well as TV. Compatible with digi links such as the SLx Link, so that a Sky box can be controlled remotely. More information on the SLx Gold DG204F.

For best results use gold plated F-plugs.

£24.50

The price listed includes VAT and delivery to anywhere in the UK.

The Labgear SDA243 is a stepped power amplifier. Many consumers do not realise that too much gain can give poor reception. This amplifier's output is stepped with 2 outputs at 8dB for short cable runs and 2 outputs at 12dB for medium and longer cable runs. So, for an amplifier positioned in a loft the 8dB outputs would go to bedrooms and the more powerful outputs to rooms further away. Two inputs (UHF and FM/DAB). Uses screw on F-plug connections. More information on the Labgear SDA243 Stepped Power Aerial Amplifier.

£22.99

The price listed includes VAT and delivery to anywhere in the UK.

SLx Gold six output aerial amplifier with F-plug connections. Designed with the professional aerial installer in mind. Digital satellite compatible. Uses screw on F-plug connections, which are gold plated. Complete with built in Tetra filter to reduce interference from emergency services Tetra radios. Built in surge and spike protection. Built in short circuit protection. Can also be used for DAB or FM radio as well as TV. Compatible with digi links such as the SLx Link, so that a Sky box can be controlled remotely. More information on the SLx Gold DG206F.

For best results use gold plated F-plugs.

£28.50

The price listed includes VAT and delivery to anywhere in the UK.

The Labgear SDA263 is a stepped power amplifier. Many consumers do not realise that too much gain can give poor reception. This amplifier's output is stepped with 2 outputs at 8dB for short cable runs, 2 outputs at 12dB for medium cable runs and 2 outputs at 16dB for long cable runs. So, for an amplifier positioned in a loft the 8dB outputs would go to bedrooms and the more powerful outputs to rooms further away. Two inputs (UHF and FM/DAB). Uses screw on F-plug connections. More information on the Labgear SDA263 Stepped Power Aerial Amplifier.

£26.99

The price listed includes VAT and delivery to anywhere in the UK.

SLx Gold DG208F - designed with the professional aerial installer in mind. Digital satellite compatible. Uses screw on F-plug connections. 25mA line powering for masthead amplifier. More information on the SLx Gold DG208F.

For best results use gold plated F-plugs.

£32.50

The price listed includes VAT and delivery to anywhere in the UK.

The Labgear SDA283 is a stepped power amplifier. Many consumers do not realize that too much gain can give poor reception. This amplifier's output is stepped with 4 outputs at 8dB for short cable runs, 2 outputs at 12dB for medium cable runs and 2 outputs at 16dB for long cable runs. So, for an amplifier positioned in a loft the 8dB outputs would go to bedrooms and the more powerful outputs to rooms further away. Two inputs (UHF and FM/DAB). Uses screw on F-plug connections. More information on the Labgear SDA283 Stepped Power Aerial Amplifier.

£29.99

The price listed includes VAT and delivery to anywhere in the UK.

The Labgear MSA263LP Aerial Amplifier is designed for professional standard installations in lofts or roof spaces with no mains power or restricted mains power. This six output amplifier can be powered by the second unit through the RF cable. Two inputs (one UHF and one VHF) and six outputs. Digital satellite compatible, so the output from a satellite box can be distributed easily. The satellite box can even be controlled from any TV connected to any one of the amplifier's outputs (except the one used for power), using a magic eye remote control systems such as the Bluedelta Smart Eye or the SLx Link. Built in Tetra filter. Uses screw on F-plug connections. Two year manufacturer's guarantee. More information on the Labgear MSA263LP Aerial Amplifier.

£36.50

The price listed includes VAT and delivery to anywhere in the UK.

The Labgear MSA283LP Aerial Amplifier is designed for professional standard installations in lofts or roof spaces with no mains power or restricted mains power. This eight output amplifier can be powered by the second unit through the RF cable. Two inputs (one UHF and one VHF) and eight outputs. Digital satellite compatible, so the output from a satellite box can be distributed easily. The satellite box can even be controlled from any TV connected to any one of the amplifier's outputs (except the one used for power), using a magic eye remote control systems such as the Bluedelta Smart Eye or the SLx Link. Built in Tetra filter. Uses screw on F-plug connections. Two year manufacturer's guarantee. More information on the Labgear MSA283LP Aerial Amplifier.

£44.50

The price listed includes VAT and delivery to anywhere in the UK.

SLx Gold 2 is designed to increase and improve TV, DAB Digital Radio and FM signals. Small unobtrusive unit designed to boost the signal to up to two TVs. Has integrated Digital By-pass for use with SLx Link to allow control of Sky Receivers from additional TVs. Built in protection against both surge/spike and short circuits. More information on the SLx Gold 2.

£18.99

The price listed includes VAT and delivery to anywhere in the UK.

SLx Gold 4 is designed to increase and improve TV, DAB Digital Radio and FM signals. Small unobtrusive unit designed to boost the signal to up to four TVs. Has integrated Digital By-pass for use with SLx Link to allow control of Sky Receivers from additional TVs. Built in protection against both surge/spike and short circuits. More information on the SLx Gold 4.

£27.99

The price listed includes VAT and delivery to anywhere in the UK.

SLx Gold 6 is designed to increase and improve TV, DAB Digital Radio and FM signals. Small unobtrusive unit designed to boost the signal to up to six TVs. Has integrated Digital By-pass for use with SLx Link to allow control of Sky Receivers from additional TVs. Built in protection against both surge/spike and short circuits. More information on the SLx Gold 6.

£31.99

The price listed includes VAT and delivery to anywhere in the UK.

SLx Gold 8 is designed to increase and improve TV, DAB Digital Radio and FM signals. Small unobtrusive unit designed to boost the signal to up to eight TVs. Has integrated Digital By-pass for use with SLx Link to allow control of Sky Receivers from additional TVs. Built in protection against both surge/spike and short circuits. More information on the SLx Gold 8.

£35.99

The price listed includes VAT and delivery to anywhere in the UK.

The Konig AMP-PRO30 is a very high powered CATV home distribution amplifier for indoor use, with return path. It is usually used to distribute satellite or cable TV to other rooms in a house. The Konig amplifier's connections are screw on F-connectors and the unit has both slope and gain control. Frequency range forward is 86 - 862 MHz and the return path is 5 - 65 MHz (Passive). The gain forward is a massive 30 dB and the gain control forward: 0~18 dB - slope control is also 0~18 dB. Power Supply is 240 V AC (so it needs to be plugged into the mains, and power consumption is 6 W. Very good for long cable runs or other installations where a powerful gain is needed. More information on the Konig AMP-PRO30 Aerial Distribution Amplifier.

£26.99

The price listed includes VAT and delivery to anywhere in the UK.

The Konig AMP-PRO30 is a very high powered CATV home distribution amplifier for indoor use, with return path. It is usually used to distribute satellite or cable TV to other rooms in a house. The Konig amplifier's connections are screw on F-connectors and the unit has both slope and gain control. Frequency range forward is 86 - 862 MHz and the return path is 5 - 65 MHz Active). The gain forward is a massive 30 dB and the gain control forward: 0~18 dB - slope control is also 0~18 dB. Power Supply is 240 V AC (so it needs to be plugged into the mains, and power consumption is 6 W. Very good for long cable runs or other installations where a powerful gain is needed. More information on the Konig AMP-PRO30A Aerial Distribution Amplifier.

£29.99

The price listed includes VAT and delivery to anywhere in the UK.

The Konig Multimedia Amplifier has 3 RF TV outputs of differing amplification. The idea is that the TV that is furthest from the amplifier is the one that is connected to the strongest output. This makes more sense than an amplifier that is flat gain and may be feeding the same strength signal to all connected TVs - both near and far. There is also a built-in splitter for Internet cable modems. More information on the Konig Multi Media 3 way Aerial Distribution Amplifier.

• Frequency range: 87 ~ 862 MHz
• Gain: Output 1: max 6 dB
• Gain Output 2: max. 8 dB
• Gain Output 3: max. 10 dB
• Return path: 5 ~ 70 MHz
• Attenuation return path: max. 1,2 dB
• Return path connector: F-type.
  

£11.99

The price listed includes VAT and delivery to anywhere in the UK.

Allows the distribution of FM radio, DAB radio, CCTV, VCR, satellite and terrestrial TV signals to 8 televisions/radios around the home from one location (e.g. loft). Combines TV, FM, DAB, CCTV and satellite signals on to one down cable. More information on the SLx8L.

£44.99

The price listed includes VAT and delivery to anywhere in the UK.

Allows the distribution of FM radio, DAB radio, CCTV, VCR, satellite and terrestrial TV signals to 4 televisions/radios around the home from one location (e.g. loft). Combines TV, FM, DAB, CCTV and satellite signals on to one down cable. The Labgear HDU641 has the LNB1 and LNB2 input and downlinks required by SkyPlus and SkyHD. More information on the Labgear HDU641.

£49.99

The price listed includes VAT and delivery to anywhere in the UK.

Allows the distribution of FM radio, DAB radio, CCTV, VCR, satellite and terrestrial TV signals to 8 televisions/radios around the home from one location (e.g. loft). Combines TV, FM, DAB, CCTV and satellite signals on to one down cable. The Labgear HDU681 has the LNB1 and LNB2 input and downlinks required by SkyPlus and SkyHD. More information on the Labgear HDU681.

£59.99

The price listed includes VAT and delivery to anywhere in the UK.

The Global SPC4 allows you to combine the output from up to four Sky boxes onto one distribution system. Not only that, but you can select which Sky box you view and control each box individually through the SPC4. You have to connect up the SPC4 to a separate distribution amplifier to feed the various TVs that you want to receive Sky on. You should use the Global TV Link magic eyes to control the Sky boxes.

£44.99

The price listed includes VAT and delivery to anywhere in the UK.

Multiswitch for satellite TV with 4 inputs for connection to up to 4 LNBs (satellite inputs and 1 terrestrial input (aerial). The Konig SAT-MS54-KN10 Multiswitch has 4 outputs for connection to either analog or digital receivers. More information on the Konig SAT-MS54-KN10 Multiswitch.

£59.99

The price listed includes VAT and delivery to anywhere in the UK.

Multiswitch for satellite TV with 4 inputs for connection to up to 4 LNBs (satellite inputs and 1 terrestrial input (aerial). The Konig SAT-MS58-KN10 Multiswitch has 8 outputs for connection to either analog or digital receivers. More information on the Konig SAT-MS58-KN10 Multiswitch.

£89.99

The price listed includes VAT and delivery to anywhere in the UK.

Non Technical

This multiswitch is of a type used usually in hotels, small blocks of flats, multi occupancy shared houses etc. You can connect up to four different satellite dish inputs and a aerial input. The multiswitch distributes all the signals down one cable and then each room or flat has a satellite decoder box or a Freeview box to decode the TV signal. If you want to you can even add DAB Digital Radio and/or FM radio signals to the aerial by using a PSF310 unit, which combines these signals into one.

Technical

This self-contained multiswitch is intended for stand-alone use in smaller Integrated Reception Systems (IRS). These compact switches have enhanced filtering to overcome the problem of LNB noise bleeding through on the UHF spectrum and increasing the noise floor. In addition the switches have increase isolation between the IF inputs which reduces the risk of missing Low Band channels. This range of switches is a cost effective solution for small to medium IRS systems.
By installing a PSF310 it allows you to combine FM, DAB and UHF on to a common cable to introduce the signals into the Terrestrial input on the switch.
The IF filter performance of these products - 25 dB rejection below 854 MHz - reduces noise and other unwanted products from the LNB in the UHF band to a negligible level.

Gain controls are provided on all inputs, allowing the switch output levels to be set to optimise delivery of weaker DTT multiplexes whilst not overloading receivers with excessive analogue signal levels. Professional multiswitch. More information on the Labgear MS512E.

£119.99

The price listed includes VAT and delivery to anywhere in the UK.

The SLx1P aerial amplifier allows the distribution of either FM radio, DAB radio, Digital Satellite and terrestrial TV signals to 1 other television or radio. Plugs into power socket directly. The SLx1P has a variable gain control switch (10-20dB). Double screened for minimal interference. More information on the SLx1P.

£9.99

The price listed includes VAT and delivery to anywhere in the UK.

The SLx2P aerial amplifier allows the distribution of either FM radio, DAB radio, Digital Satellite and terrestrial TV signals to 2 other televisions or radios. Plugs into power socket directly. The SLx2P has a variable gain control switch (10-20dB). Double screened for minimal interference. More information on the SLx2P.

£11.99

The price listed includes VAT and delivery to anywhere in the UK.

This kit combines a high gain 1 way masthead amplifier with a power supply. Giving power gain of 26dB.

Amplifier
• Operating frequency 470-862MHz
• Noise figure <2dB
• Gain is 26dB
• Built-in Tetra filter
• Weatherproof outer plastic housings with foam cable seal
• Fully screened, sealed, die-cast modules
• F-connectors throughout
• Ideal for digital
• Fixing options: standard cable tie mast mount or flat surface fix
• Earth bonding terminals

Power Supply
• F-type connections.
• With fitted mains plugs to BS 1363.
• Excellent screening helps prevent ingress of impulse interference in DTT installations.
• Output short-circuit protection with LED fault indication.
• Thermal fuse in mains transformer protects against overheating.

The connection for these amplifiers (and the power supply) re F-Plugs. F-plugs are ideal if you want a connection that is super-secure. An F-plug coaxial connection screws on. If you need F-Plugs that can be crimped on to your coaxial cable then you can find plugs and crimping tools on our Coaxial Accessories page.

£17.99

The price listed includes VAT and delivery to anywhere in the UK.

This kit combines a high gain 1 way masthead amplifier with a power supply with adjustable output allowing indoor gain control. This means that with the power supply positioned within sight of a TV the gain can be adjusted easily for optimum picture quality.
Power Gain can be adjusted from 9-26dB.

Amplifier
• Operating frequency 470-862MHz
• Noise figure <2dB
• Gain can be adjusted from 9-26dB
• Built-in Tetra filter
• Weatherproof outer plastic housings with foam cable seal
• Fully screened, sealed, die-cast modules
• F-connectors throughout
• Ideal for digital
• Fixing options: standard cable tie mast mount or flat surface fix
• Earth bonding terminals

Power Supply
• Built-in adjustable attenuator allows gain control of signal output
• F-type connections.
• With fitted mains plugs to BS 1363.
• Excellent screening helps prevent ingress of impulse interference in DTT installations.
• Output short-circuit protection with LED fault indication.
• Thermal fuse in mains transformer protects against overheating.

The connection for these amplifiers (and the power supply) are F-Plugs. F-plugs are ideal if you want a connection that is super-secure. An F-plug coaxial connection screws on. If you need F-Plugs that can be crimped on to your coaxial cable then you can find plugs and crimping tools on our Coaxial Accessories page.

£22.99

The price listed includes VAT and delivery to anywhere in the UK.

Theses power supplies will power any mast head amplifier through the coaxial cable. There are two versions one with a flat power output and one with a variable output. The variable version contains a built in attenuator which allows you to control the gain of the masthead amplifier.

• Built-in adjustable attenuator allows gain control of signal output (PSM114V only)
• F-type connections.
• With fitted mains plugs to BS 1363.
• Excellent screening helps prevent ingress of impulse interference in DTT installations.
• Output short-circuit protection with LED fault indication.
• Thermal fuse in mains transformer protects against overheating.

The connection for these power supply are F-Plugs. F-plugs are ideal if you want a connection that is super-secure. An F-plug coaxial connection screws on. If you need F-Plugs that can be crimped on to your coaxial cable then you can find plugs and crimping tools on our Coaxial Accessories page.

Labgear PSM114 Masthead Amplifier Power Supply £10.99
Labgear PSM114V Masthead Amplifier Power Supply £14.99

This kit combines a high gain 1 way masthead amplifier with a power supply and adjustable gain control. The power gain can be adjusted from 17-27dB via a gain switch on the amplifier itself. Made in Europe.

Amplifier
• Operating frequency 470-862MHz
• Noise figure 1.4dB
• Gain can be adjusted from 17-27dB
• Gold plated F-Plugs
• Ventilated ABS weatherproof molding IP53 rated
• Fully screened, sealed, die-cast modules
• Built-in adjustable attenuator allows gain control of signal output
• Ideal for digital
• Fixing options: standard cable tie mast mount or flat surface fix
• Earth bonding terminals

Power Supply
• F-type connections.
• With fitted mains plugs to BS 1363.
• Very low power consumption (45mA)
• Low energy 5V 60mA with short circuit and overload protection

The connection for these amplifiers (and the power supply) re F-Plugs. F-plugs are ideal if you want a connection that is super-secure. An F-plug coaxial connection screws on. If you need F-Plugs that can be crimped on to your coaxial cable then you can find plugs and crimping tools on our Coaxial Accessories page.

£24.99

The price listed includes VAT and delivery to anywhere in the UK.

This kit combines a high gain 4 way masthead amplifier with a power supply with adjustable output allowing indoor gain control. This means that with the power supply positioned within sight of a TV the gain can be adjusted easily for optimum picture quality.
Power Gain can be adjusted from 9-26dB.

Amplifier
• Operating frequency 470-862MHz
• Noise figure <2dB
• Gain can be adjusted from 9-26dB
• Built-in Tetra filter
• Weatherproof outer plastic housings with foam cable seal
• Fully screened, sealed, die-cast modules
• F-connectors throughout
• Ideal for digital
• Fixing options: standard cable tie mast mount or flat surface fix
• Earth bonding terminals

Power Supply
• Built-in adjustable attenuator allows gain control of signal output
• F-type connections.
• With fitted mains plugs to BS 1363.
• Excellent screening helps prevent ingress of impulse interference in DTT installations.
• Output short-circuit protection with LED fault indication.
• Thermal fuse in mains transformer protects against overheating.

The connection for these amplifiers (and the power supply) re F-Plugs. F-plugs are ideal if you want a connection that is super-secure. An F-plug coaxial connection screws on. If you need F-Plugs that can be crimped on to your coaxial cable then you can find plugs and crimping tools on our Coaxial Accessories page.

£27.99

The price listed includes VAT and delivery to anywhere in the UK.

This kit combines a high gain 4 way masthead amplifier with a power supply and adjustable gain control. The power gain can be adjusted from 10-20dB via a gain switch on the amplifier itself. Made in Europe.

Amplifier
• Operating frequency 470-862MHz
• Noise figure 1.4dB
• Gain can be adjusted from 10-20dB
• Gold plated F-Plugs
• Ventilated ABS weatherproof molding IP53 rated
• Fully screened, sealed, die-cast modules
• Built-in adjustable attenuator allows gain control of signal output
• Ideal for digital
• Fixing options: standard cable tie mast mount or flat surface fix
• Earth bonding terminals

Power Supply
• F-type connections.
• With fitted mains plugs to BS 1363.
• 12V 100mA with short circuit and overload protection

The connection for these amplifiers (and the power supply) re F-Plugs. F-plugs are ideal if you want a connection that is super-secure. An F-plug coaxial connection screws on. If you need F-Plugs that can be crimped on to your coaxial cable then you can find plugs and crimping tools on our Coaxial Accessories page.

£29.99

The price listed includes VAT and delivery to anywhere in the UK.

The SLx range of UHF TV antenna preamplifiers are designed for the professional aerial installer and the competent DIY installer. The SLx Masthead Amplifiers are great for areas with poor signal strength or when you would like to receive an out of area transmission.
Ideal where long cable runs are necessary (where the loss is greater than 5dB). 9dB, 15dB or 26dB gain. These SLx Masthead Amplifiers require a 12V DC power supply, this can be connected via the down lead cable, either by dedicated power supply unit (also shown here) or from a distribution amplifier with line powering (such as the SLx 4, SLx 6 and SLx 8).

Many people make the mistake of assuming that a 26dB amplifier is going to be what they need because as it is the most powerful it must be best. In fact, too much gain can be as bad as not enough. You may need to do some research, as the boost that you need depends upon your distance from the transmitter, which transmitter it is etc. You can find out a lot on the Internet and you could also always try asking your neighbours what they do, the chances are if you have TV reception problems they do too.

The connection for these amplifiers (and the power supply) is an ordinary push on coaxial connection. The exception to this is the F-Plug versions 9dB and 26dB. This is ideal if you want a connection that is super-secure. An F-plug coaxial connection screws on. If you need F-Plugs that can be crimped on to your coaxial cable then you can find plugs and crimping tools on our Coaxial Accessories page.

The price listed includes VAT and delivery to anywhere in the UK.

SLx 9dB Masthead Amplifier (F-Plug Connections) £7.99
Mercury 12dB Masthead Amplifier £8.99
SLx 15dB Masthead Amplifier £9.99
Mercury 22dB Masthead Amplifier £12.99
SLx 26dB Masthead Amplifier £13.99
SLx Masthead Amplifier Power Supply £8.99

If you are struggling to receive some of the digital terrestrial channels clearly or are experiencing picture break up on your TV, this may be due to being in a very poor signal area and a signal booster may be required.

When connected between your aerial and TV/Set top box, a booster will amplify the signal being received from your closest TV transmitter. The now amplified signal should then give you more chance of receiving a clearer, stronger and more stable picture.

The 12/24V DC Variable Gain Signal Booster (VSB12) is designed for use in touring applications to boost and distribute both TV and FM signals. The Maxview VSB1M12 12 Volt TV Signal Booster features a variable gain control, allowing for optimum signal adjustment to give the best possible picture and sound quality. It is suitable for indoor use only and comes complete with easy to follow fully illustrated instructions.

If you need Coaxial plugs that can be crimped or screwed onto your coaxial cable then you can find plugs and crimping tools on our Coaxial Accessories page.

£19.99

The price listed includes VAT and delivery to anywhere in the UK.

Labgear PSC120 2-way VHF/UHF combiner / splitter

• 5-1000 MHz
• 3.7dB insertion loss
• 75 §Ù impedance
• Power passes in both directions
• Ideal for splitting the Uplink on an HDU installation
• Weatherproof outer plastic housings with foam cable seal
• Fully screened, sealed, die-cast modules
• F-connectors throughout
• Ideal for digital
• Fixing options: standard cable tie mast mount or flat surface fix
• Earth bonding terminals

£11.99